2010 Dodge Ram Pickup 2500 Oil Change in Danvers, MA

Yes—dealer oil changes include OEM-spec oil and a Mopar filter plus a documented multi-point inspection at Herb Chambers Chrysler Dodge Jeep RAM FIAT of Danvers.

For a 2010 Dodge Ram Pickup 2500, using fluids that meet Chrysler specs helps protect the 5.7L V8 and preserves maintenance records. Our Danvers, MA team follows factory procedures and updates your service history—useful for warranty work and resale. You can also review current offers before you book.

• OEM-spec oil and Mopar filter installed
• Documented multi-point inspection and fluid top-offs
• Book online: schedule service and check service specials

Skipping or delaying oil changes can jeopardize warranty coverage if you can’t show maintenance was performed per the factory schedule.

Keep dated receipts and follow the OEM maintenance schedule for your 2010 Dodge Ram Pickup 2500 to avoid coverage disputes. Warranty work generally requires documentation and a certified facility, which our Danvers service center provides. Save your records and book ahead to stay on track.

• Maintain dated invoices or service logs
• Certified facility helps with warranty documentation
• Book online: schedule service

Conventional is mineral-based, synthetic blend mixes base stocks, and full synthetic offers the best high-temp stability and cold-start protection.

Your 2010 Dodge Ram Pickup 2500 benefits from oil that maintains viscosity in New England winters and under towing heat. Full synthetic typically controls deposits better and resists breakdown during stop-and-go Greater Boston traffic. Always use oil that meets Chryslers specification for this engine.

• Better cold-start pumpability with full synthetic
• Improved oxidation resistance under load/towing
• Use oil that meets Chryslers required spec

The 2010 Dodge Ram Pickup 2500 5.7L V8 specifies SAE 5W-20 oil that meets Chrysler MS-6395.

Using the correct viscosity and specification helps protect timing components, lifters, and bearings in your 5.7L V8. Full synthetic that meets MS-6395 is acceptable and can improve cold-start protection in Danvers, MA winters. Our technicians install OEM-spec oil and a Mopar filter to match factory guidance.

• Viscosity: SAE 5W-20 (per factory spec)
• Meets: Chrysler MS-6395
• Installed with Mopar-grade filter in Danvers

The 2010 Dodge Ram Pickup 2500 5.7L V8 typically takes about 7.0 quarts with a filter change.

Capacity matters for proper lubrication, especially when your truck tows or idles in traffic. Our team measures drained volume, replaces the Mopar filter, fills to spec, and verifies the level after a short run. This approach supports consistent pressure and longevity.

• Approximate fill: 7.0 quarts with filter
• Level verified hot after initial run
• OEM-spec oil and filter included

Change the oil about every 6,000 miles or 6 months under normal driving; use around 3,000 miles for severe duty.

Severe duty for a 2010 Dodge Ram Pickup 2500 includes frequent short trips in cold weather, heavy towing, or dusty job sites—common around the North Shore. New England winters and stop-and-go around Greater Boston justify tighter intervals. Well document each visit to keep your maintenance history complete.

• Normal: ~6,000 miles/6 months
• Severe: ~3,000 miles (towing, cold starts, dust)
• Book online: schedule service

Plan for about 45960 minutes for a standard oil and filter change appointment in Danvers.

Time can vary slightly based on shop volume and added inspections, but we work efficiently while following factory procedures. Your 2010 Dodge Ram Pickup 2500 receives an OEM-spec oil fill, Mopar filter, and a multi-point check. You can pick a convenient time online.

• Typical bay time: ~45960 minutes
• Includes inspection and fluid top-offs
• Reserve a slot: schedule service

Expect transparent, up-front pricing with OEM-spec oil, a Mopar filter, and disposal included; check our current service specials for the latest offers.

Actual cost depends on oil type and your 2010 Dodge Ram Pickup 2500s needs. Well confirm the estimate before work begins and apply eligible coupons. Review deals, then lock in your time at our Danvers, MA service center.

• OEM-spec oil and Mopar filter included
• Up-front estimate before work starts
• See service specials and schedule

Your 2010 Dodge Ram Pickup 2500 receives a methodical service designed for durability and record-keeping. We safely lift the truck, drain used oil, replace the drain gasket as needed, and install a Mopar-grade filter matched to the 5.7L V8. We then fill with oil that meets Chryslers specification, start the engine, verify pressure, and top off to the dipsticks correct mark. A multi-point inspection follows, covering brakes, tires, battery health, belts/hoses, and visible leaks. We also adjust tire pressures and top off serviceable fluids. Youll leave with a printed or digital record for your maintenance file. Ready to plan your visit? Use our online tool to schedule service or review current service specials before you arrive.

For the 2010 Dodge Ram Pickup 2500 with the 5.7L V8, the factory calls for SAE 5W-20 engine oil that meets Chrysler MS-6395. Full synthetic that meets this spec offers strong cold-start pumpability for Danvers winters and added high-temperature stability for towing or job-site idling. Typical refill is about 7.0 quarts with a filter change; our team verifies the level after an initial run. We install an OEM-quality Mopar oil filter designed for the HEMIs flow and filtration needs. Follow the manufacturers recommended interval, and shorten it for severe duty like frequent short trips, dusty sites, or heavy towing. Bring your 2010 Dodge Ram Pickup 2500 to Herb Chambers Chrysler Dodge Jeep RAM FIAT of Danvers in Danvers for an OEM-spec oil change — schedule service.

We proudly serve the North Shore and Greater Boston—including Peabody, Beverly, Lynnfield, Andover, and Salem—right from 107 Andover St (Route 114), Danvers, MA 01923. Local conditions shape oil needs for a 2010 Dodge Ram Pickup 2500: cold-starts in winter favor low-temp pumpability, road salt and stop-and-go traffic stress lubricants, and towing or hauling raises oil temperatures. Our factory-certified, OEM-trained technicians use fluids that meet Chrysler specifications and complete a documented multi-point inspection at each visit. Book online to match your schedule, and review our latest offers to manage costs. Need directions or to lock in a time? Schedule an appointment and check service specials before you arrive.